ignite4

How to recover a system from an Ignite-UX boot tape

Interrupt system boot

Firmware Version 24.4

Duplex Console IO Dependent Code (IODC) revision 2

--------------------------------------------------------------------------

Cab/ Cell ------- Processor -------- Cache Size

Cell Slot State # Speed State Inst Data

---- ---- ------------ --- -------- ----------- ------ ------

3 0/3 Active 0A 1000 MHz Active 32 MB 32 MB

0B 1000 MHz Idle 32 MB 32 MB

1A 1000 MHz Idle 32 MB 32 MB

1B 1000 MHz Idle 32 MB 32 MB

2A 1000 MHz Idle 32 MB 32 MB

2B 1000 MHz Idle 32 MB 32 MB

3A 1000 MHz Idle 32 MB 32 MB

3B 1000 MHz Idle 32 MB 32 MB

Primary Boot Path: 3/0/1/1/0/4/0.0

Boot Actions: Boot from this path.

If unsuccessful, go to BCH.

HA Alternate Boot Path: 0/0/0/0/0.0

Boot Actions: Skip this path.

Go to next path.

Alternate Boot Path: 3/0/11/1/0/4/0.0

Boot Actions: Go to BCH.

Console Path: 3/0/0/0/0.0

Attempting to boot using the primary path.

-------------------------------------------------------------

To discontinue, press any key within 10 seconds.

Boot terminated.

---- Main Menu ---------------------------------------------------------------

Command Description

------- -----------

BOot [PRI|HAA|ALT|<path>] Boot from specified path

PAth [PRI|HAA|ALT] [<path>] Display or modify a path

SEArch [ALL|<cell>|<path>] Search for boot devices

ScRoll [ON|OFF] Display or change scrolling capability

COnfiguration menu Displays or sets boot values

INformation menu Displays hardware information

SERvice menu Displays service commands

DIsplay Redisplay the current menu

HElp [<menu>|<command>] Display help for menu or command

REBOOT Restart Partition

RECONFIGRESET Reset to allow Reconfig Complex Profile

----

Main Menu: Enter command or menu > sea ipl

ERROR: Unknown device

Search Table has been cleared

Main Menu: Enter command or menu > search

Searching for potential boot device(s) on the core cell

This may take several minutes.

To discontinue search, press any key (termination may not be immediate).

IODC

Path# Device Path (dec) Device Type Rev

----- ----------------- ----------- ----

P0 3/0/1/1/0/4/0.0 Random access media 4

3/0/4/1/0/4/0.0 Fibre Channel Protocol 14

3/0/6/1/0/4/0.0 Fibre Channel Protocol 14

P1 3/0/11/1/0/4/0.0 Random access media 4

P2 3/0/11/1/0/4/1.2 Random access media 4

P3 3/0/11/1/0/4/1.0 Sequential access media 4

3/0/12/1/0/4/0.0 Fibre Channel Protocol 14

3/0/14/1/0/4/0.0 Fibre Channel Protocol 14

Main Menu: Enter command or menu > bo P3

BCH Directed Boot Path: 3/0/11/1/0/4/1.0

Do you wish to stop at the ISL prompt prior to booting? (y/n) >> n

Initializing boot Device.

Boot IO Dependent Code (IODC) Revision 4

Boot Path Initialized.

HARD Booted.

ISL Revision A.00.44 Mar 12, 2003

ISL booting hpux (;0):INSTALL

Boot

: tape(3/0/11/1/0/4/1.0.0.0.0.0.0;0):WINSTALL

24133632 + 5544944 + 8117232 start 0x2660e8

DoCalllist done

ktune_get: tunable vm_fast_boot_enable not found, proceeding with failsafe value 0

gate64: sysvec_vaddr = 0xc0002000 for 2 pages

Memory Class Setup

-------------------------------------------------------------------------

Class Physmem Lockmem Swapmem

-------------------------------------------------------------------------

System : 31141 MB 31141 MB MB

User :initialization.

rpc_initn associated with the LUN FC/GigE Combo Adapter at figured on root device; ig * Preparing to execute init...

======= 06/18/15 09:16:26 EDT HP-UX Installation Initialization.

@(#)Ignite-UX Revision C.7.15.254

@(#)ignite/launch (opt) Revision:

/branches/IUX_RA1209/ignite/src@84961 Last Modified: 2012-07-24

17:39:58 +0530 (Tue, 24 Jul 2012)

* Configuring RAM filesystems...

* Scanning system for IO devices...

* Boot device is: 3/0/11/1/0/4/1.0x0.0x0

catRecovery tape created from system: ibtest on Wed Apr 29 17:01:01 2015

WARNING: The configuration information calls for a non-interactive

installation.

Press <Return/Enter> within 10 seconds to cancel batch-mode installation:

* Using client directory: /var/opt/ignite/clients/0x000F203CB2F4

* Checking configuration for consistency...

NOTE: Dump space (12582912KB) is less than 50% of system memory

(33526784KB). There is a possibility that the system dump will be

truncated with a failure to capture important system information in

the event of a system crash. You can increase the size of the dump

volumes or add additional dump volumes on the "File System" tab when

using the advanced user interface. See crashconf(1M) for more

information.

WARNING: Free space (4794720KB) in "/var" where /var/adm/crash is located is

less than 25% of system memory (33526784KB). This will likely result

in an inability to capture a single selective compressed dump in the

event of a system crash. Additional space will be required to

uncompress the dump in order to analyze it and to save multiple dumps.

You can increase the size of the "/var" volume on the "File System"

tab when using the advanced user interface.

WARNING: The disk at: 3/0/1/1/0/4/0.0x0.0x0 (COMPAQ_BD07287B4C) appears to

contain a file system and boot area. Continuing the installation will

destroy any existing data on this disk.

WARNING: The disk at: 3/0/11/1/0/4/0.0x0.0x0 (COMPAQ_BD07287B4C) appears to

contain a file system and boot area. Continuing the installation will

destroy any existing data on this disk.

Press <Return/Enter> within 10 seconds to cancel batch-mode installation:

Really cancel non-interactive install and start the

user-interface? ([y]/n): Invalid response, enter 'y' or 'n'

Really cancel non-interactive install and start the

user-interface? ([y]/n): y

* Setting keyboard language to: PS2_DIN_US_English.

Recovery tape created from system: ibtest on Wed Apr 29 17:01:01 2015

Use Ignite-UX interface

Use the Ignite-UX itool interface to properly configure system network configuration and to verify in which boot drive will the HP-UX be installed.

Welcome to Ignite-UX!

Use the <tab> key to navigate between fields, and the arrow keys

within fields. Use the <return/enter> key to select an item.

Use the <return/enter> or <space-bar> to pop-up a choices list. If the

menus are not clear, select the "Help" item for more information.

Hardware Summary: System Model: 9000/800/SD32A

+----------------------+---------------+--------------------+[ Scan Again ]

| Disks: 261(13406.6GB)| Floppies: 0 | LAN cards: 9 |

| CD/DVDs: 1 | Tapes: 1 | Memory: 32741Mb |

| Graphics Ports: 0 | IO Buses: 9 | CPUs: 8 |[ H/W Details ]

+----------------------+---------------+--------------------+

[ at * Initiating hardware rescan...

* Scanning system for IO devices...

[ Run an Expert Recovery Shell ]

[ Advanced Options ]

[ Read Sys-Admin Message ]

[ Reboot ] [ Help ]

+ /opt/ignite/bin/itool () +

| |

| +-------++----------++--------++-------------++----------+ |

| | Basic || Software || System || File System || Advanced | |

| | \-------------------------------------------------------------------+|

| | ||

| | Configurations: [ Recovery Archive ->] [ Description... ] ||

| | ||

| | Environments: [ Recovery Archive ->] (HP-UX B.11.31) ||

| | ||

| | [ Root Disk ] COMPAQ_BD07287B4C, 3/0/1/1/0/4/0.0x0.0x0> ||

| | ||

| | File System: [ HP-UX save_config layout ->] ||

| | ||

| | [ Root Swap (MB)... ] 12288 Physical Memory (RAM) = 32741 MB ||

| | ||

| | [ Languages... ] English [ Keyboards... ] [ Additional... ]||

| | ||

| +---------------------------------------------------------------------------+|

| [ Show Summary... ] [ Reset Configuration ] |

|------------------------------------------------------------------------------|

| [ Go! ] [ Cancel ] [ Help ] |

+------------------------------------------------------------------------------+

Use [ Go ! ] buttom

When all the settings has been checked, use the GO buttom in start "igniting" the server.

Note: The server will automatically reboot after recovering the archive. It will reboot a second time after rebuilding the device special files.

* Loading configuration utility...

* Beginning installation from source: /dev/rmt/c3t0d0BEST

======= 06/18/15 09:33:28 EDT Starting system configuration...

* Configure_Disks: Begin

* Mapping LUN Instance Data

ioinit: Instance number 244 already exists for class disk.

Line 6. 3/0/4/1/0/4/0.17.220.0.0.2.1 disk 244

ERROR: ioinit failed

insf: Installing special files for asio0 instance 0 address 3/0/0/0/0

insf: Installing special files for sdisk instance 0 address 3/0/1/1/0/4/0.0.0

insf: Installing special files for sctl instance 0 address 3/0/1/1/0/4/0.15.0

insf: Installing special files for sdisk instance 4 address 3/0/4/1/0/4/0.17.192.0.0.0.0

insf: Installing special files for sdisk instance 11 address 3/0/4/1/0/4/0.17.192.0.0.0.1

insf: Installing special files for sdisk instance 22 address 3/0/4/1/0/4/0.17.192.0.0.0.2

insf: Installing special files for sdisk instance 27 address 3/0/4/1/0/4/0.17.192.0.0.0.3

insf: Installing special files for sdisk instance 36 address 3/0/4/1/0/4/0.17.192.0.0.0.4

insf: Installing special files for sdisk instance 42 address 3/0/4/1/0/4/0.17.192.0.0.0.5

insf: Installing special files for sdisk instance 52 address 3/0/4/1/0/4/0.17.192.0.0.0.6

insf: Installing special files for sdisk instance 58 address 3/0/4/1/0/4/0.17.192.0.0.0.7

…Output Shortened.

insf: Installing special files for esctl instance 12 address 64000/0xfa00/0x106

insf: Installing special files for esdisk instance 2335 address 64000/0xfa00/0x107

insf: Installing special files for estape instance 1 address 64000/0xfa00/0x108

insf: Installing special files for esdisk instance 2336 address 64000/0xfa00/0x109

insf: Installing special files for pseudo driver cn

insf: Installing special files for pseudo driver diag2

insf: Installing special files for pseudo driver root

insf: Installing special files for pseudo driver escsi

* Boot device is: 3/0/11/1/0/4/1.0x0.0x0

[Read-only - use ^Ecf to attach to console.]

* Will install B.11.31 onto this system.

* Using LVM for disk 3/0/1/1/0/4/0.0x0.0x0 (disk2136), group: vg00

* Using LVM for disk 3/0/11/1/0/4/0.0x0.0x0 (disk2335), group: vg00

* Creating LVM physical volume "/dev/rdisk/disk2335" (3/0/11/1/0/4/0.0x0.0x0).

* Creating LVM physical volume "/dev/rdisk/disk2136" (3/0/1/1/0/4/0.0x0.0x0).

* Creating volume group "vg00".

* Creating logical volume "vg00/lvol1" (/stand).

* Creating logical volume "vg00/lvol2" (swap_dump).

* Creating logical volume "vg00/lvol3" (/).

* Creating logical volume "vg00/lvol4" (/home).

* Creating logical volume "vg00/lvol5" (/opt).

* Creating logical volume "vg00/lvol6" (/tmp).

* Creating logical volume "vg00/lvol7" (/usr).

* Creating logical volume "vg00/lvol8" (/var).

* Creating logical volume "vg00/lv_autosys" (/autosys).

* Creating logical volume "vg00/lv_ctsausr" (/ctsausr).

* Extending logical volume "vg00/lvol1" (/stand).

* Extending logical volume "vg00/lvol2" (swap_dump).

* Extending logical volume "vg00/lvol3" (/).

* Extending logical volume "vg00/lvol4" (/home).

* Extending logical volume "vg00/lvol5" (/opt).

* Extending logical volume "vg00/lvol6" (/tmp).

* Extending logical volume "vg00/lvol7" (/usr).

* Extending logical volume "vg00/lvol8" (/var).

* Extending logical volume "vg00/lv_autosys" (/autosys).

* Extending logical volume "vg00/lv_ctsausr" (/ctsausr).

* Making HFS filesystem for "/stand", (/dev/vg00/rlvol1).

* Making VxFS filesystem for "/", (/dev/vg00/rlvol3).

cat * Making VxFS filesystem for "/home", (/dev/vg00/rlvol4).

* Making VxFS filesystem for "/opt", (/dev/vg00/rlvol5).

* Making VxFS filesystem for "/tmp", (/dev/vg00/rlvol6).

* Making VxFS filesystem for "/usr", (/dev/vg00/rlvol7).

* Making VxFS filesystem for "/var", (/dev/vg00/rlvol8).

* Making VxFS filesystem for "/autosys", (/dev/vg00/rlv_autosys).

* Making VxFS filesystem for "/ctsausr", (/dev/vg00/rlv_ctsausr).

* Setting rotational delay to 0 for "/stand".

* Configure_Disks: Complete

* Download_mini-system: Begin

[Read-only - use ^Ecf to attach to console.]

x ./sbin/fs/hfs/mkfs, 356352 bytes, 696 tape blocks

x ./sbin/fs/hfs/newfs, 278528 bytes, 544 tape blocks

x ./sbin/fs/vxfs/mkfs, 1515520 bytes, 2960 tape blocks

x ./sbin/fs/vxfs/newfs, 413696 bytes, 808 tape blocks

x ./sbin/fs/vxfs5.0/mkfs, 1589248 bytes, 3104 tape blocks

x ./sbin/fs/vxfs5.0/newfs, 929792 bytes, 1816 tape blocks

x ./sbin/mkfs symbolic link to ./fs_wrapper

x ./sbin/newfs symbolic link to ./fs_wrapper

x ./sbin/lib/mfsconfig.d/hfs, 1057 bytes, 3 tape blocks

x ./sbin/lib/mfsconfig.d/vxfs5.0, 3448 bytes, 7 tape blocks

x ./sbin/fs_wrapper, 294912 bytes, 576 tape blocks

x ./sbin/sh, 487424 bytes, 952 tape blocks

x ./usr/sbin/tunefs, 28672 bytes, 56 tape blocks

x ./sbin/extendfs symbolic link to ./fs_wrapper

x ./sbin/fs/vxfs5.0/extendfs, 1536000 bytes, 3000 tape blocks

x ./sbin/fs/hfs/extendfs, 307200 bytes, 600 tape blocks

x ./sbin/lvchange symbolic link to ./lvm_wrapper

x ./sbin/lvcreate symbolic link to ./lvm_wrapper

x ./sbin/lvdisplay symbolic link to ./lvm_wrapper

x ./sbin/lvextend symbolic link to ./lvm_wrapper

x ./sbin/lvlnboot symbolic link to ./lvm_wrapper

x ./sbin/lvreduce symbolic link to ./lvm_wrapper

x ./sbin/lvremove symbolic link to ./lvm_wrapper

x ./sbin/lvrmboot symbolic link to ./lvm_wrapper

x ./sbin/pvchange symbolic link to ./lvm_wrapper

x ./sbin/pvcreate symbolic link to ./lvm_wrapper

x ./sbin/pvdisplay symbolic link to ./lvm_wrapper

x ./sbin/pvmove symbolic link to ./lvm_wrapper

Output Shortned

x ./dev/root, 0 bytes, 0 blocks, character device

x ./dev/tty, 0 bytes, 0 blocks, character device

x ./dev/syscon, 0 bytes, 0 blocks, character device

x ./dev/systty, 0 bytes, 0 blocks, character device

x ./tmp/set_locale, 3305 bytes, 7 tape blocks

x ./configure3, 2146304 bytes, 4192 tape blocks

x ./monitor_bpr, 1593344 bytes, 3112 tape blocks

* Download_mini-system: Complete

* Loading_software: Begin

* Installing boot area on disk.

* Enabling swap areas.

* Number of archives to install: 1

* Processing the archive source (Recovery Archive).

* Thu Jun 18 09:42:33 EDT 2015: Starting archive load of the source (Recovery Archive).

* Positioning the tape (/dev/rmt/c3t0d0BESTn).

* Looking for Archive...

cat * Found the Archive Position. Now load the Archive.

* Archive extraction from tape is beginning. Please wait.

* Thu Jun 18 10:44:30 EDT 2015: Completed archive load of the source (Recovery Archive).

* Executing user specified script: "/opt/ignite/data/scripts/os_arch_post_l".

* Running in recovery mode (os_arch_post_l).

* Relocating RAM filesystems.

* Running the ioinit command ("/sbin/ioinit -c")

* Creating device files via the insf command.